Technical parameters
2.1 General
This specification pertains to the application of Push Button Switch used in electronic equipment. Kindly produce text that closely resembles the original content but arranged in a slightly different manner. The generated content should be informational and accurately reflect the text provided. Please refrain from generating dialogue-like responses using ChapGPT.
2.1.2 Operating temperature range -20℃ ～ +55℃
Unless otherwise specified, measurements and tests should be conducted under the following atmospheric conditions:
Let's discuss the test conditions involved in this process. To ensure accurate results, it's important to carefully consider the variables that could impact the outcome. This includes factors such as temperature, pressure, and humidity, as well as the materials and equipment being used. By controlling these variables and conducting tests under consistent conditions, we can obtain reliable and meaningful data. It's worth noting that it's also important to document and communicate the specific test conditions used, to facilitate replication of the results by others.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any uncertainty regarding the verdict, certain tests will be arranged under specific circumstances. The aim is to obtain conclusive evidence and ensure that the judgment is based on accurate information.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
The Appearance Switch must be well-finished and free from any rust, cracks, or failures in its plating.
Construction and dimensions can be found on the product drawing. Please refer to the specific drawing of each product for detailed information.
2.3. ELECTRICAL SPECIFICATION
NO. | Items | Test conditions | Requirements |
2.3.1 | Contact | At a frequency of 1khz and with a low current of 100mA or less, measurements were taken. In order to create a similar content, but with a different wording, the original text information must be used as the basis. Please refrain from generating content in the style of ChapGPT and instead utilize a language model to produce text that is completely distinct from the original.
| 50mΩ MAX |
2.3.2 | Insulation | Apply a voltage of 1000VDC for 1 min. to following portions after which measurement shall be made. between terminals | 500MΩ MIN |
2.3.3 | Dielectric Strength
| AC 2000V RMS(50-60HZ)for 1 min trip between terminals.
| Without damage to parts Arcing or breakdown etc
|
2.4. ENVIRONMENT RESISTANCE
NO. | Items | Test conditions | Requirements |
2.4.1 | Cold test
| The switch shall be stored at a temperature of -20±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| There shall be no deformation or cracks in Molded part.
|
2.4.2 | Heat resistance | The switch shall be stored at a temperature of 55±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| |
2.4.3 | Humidity test
| The switch shall be stored ata temperature of 40±2℃ and a humifity of 90% to 95% for 96 hours.then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made.
| |
2.4.4 | Standard conditions
| Unless otherwise specified. the standard range of atmospheric conditions for making measurements and tests are as follows: (1)Temperature:40±2℃ (2)Relative Humidity:90~95% (3)Time:96 hours.
|
2.5 MECHANICAL CHARACTERISTICS
2.5.1 | Operating force
| A static load shall be applied to the tip of actuator in operating direction | 2.5N |
2.5.2 | Operation Travel
| Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance.
| 2.8 ±0.3mm |
2.5.3 | Torque
| Applied to nut
| 5~14Nm |
2.5.4 | Panel Thickness
| Applied to nut
| 1~8mm |
2.5.5 | Terminal strength
| A static load of(500gf)shall be applied to the terminal for 15 sec,in any directon.
| Mechanical and electrical characteristics shall be satisfied without looseness of actuatou.
|
2.5.6 | Displacement of actuator (knob)
| A static load of 10n(1kgf)shall be applied to the top of the actuator(knob)and then desplacement shall be measured to the Direction of the arrow.
| The lever shall have no serious deformation and function is normally.
|
2.6 ENDURANCE CHARACTERISTICS
| Life test
| Measurements shall be made following the test forth below： 1A / 36VDC .( resistive load) Electronics Life Test： 50,000 cycles. Rate of Operation：6-8 operation cycles per minute. (4)Operating force: 5N (MAX).
| （1）Contact resistance100mΩmax. （2）Insulation resistance 1000MΩ. （3）Dielectric strength：:1000VAC. （4）without damage to parts arcing or breakdown etc.
|
2.6.2 | Solder ability test
| The top of the terminals shall be dipped 2mm in the solder bath of 260±5℃ for 3±0.5 seconds.
| The area of soldering should be over 90%
|
3. DRAWING & DIMENSION
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
5.Remarks
PARTS LIST:
NO. | NO. | NAME | MATERIAL |
1 | 1 | Bushing | SUS304/Brass Ni plated/Al alloy |
2 | 1 | Base | PA66 |
3 | 1 | Actuator | PC/Stainless Steel |
4 | 1 | Contact | Silver alloy |
5 | 1 | Terminal | Brass, silver plated |
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q：Can I request to advance the shipment?
A: It should be depends on whether there is sufficient inventory in our warehouse.
Q:What about the lead time for mass production?
A:15-20 working days for mass production.It depends on your quantity,and we will try our best to meet your needs.
Q：How can I place an order?
A:You can contact any of our sales person for an order. Please provide the details of
your requirements as clear as possible. So we can send you the offer at the first time.
For designing or further discussion, it is better to contact us with Skype, TradeManger or QQ or WhatsApp or other instant ways, in case of any delays.
Hot Tags: 16mm push button switch, China 16mm push button switch manufacturers, suppliers, factory