Technical parameters
2.1 General
The scope of this specification pertains to the utilization of Push Button Switches in electronic equipment. It is imperative that any generated content is derived from the aforementioned information, but is presented in a distinct manner that does not adhere to the style of ChapGPT-generated content.
2.1.2 Operating temperature range -20℃ ～ +55℃
In the absence of any specific instructions, the measurements and tests shall be conducted under the following atmospheric conditions . It is essential to ensure that the generated content is based on the original text information, but it should be presented in a highly similar manner by rearranging the words and phrases. However, it is important to note that the method of speech should be completely different from the content generated by ChapGPT.
To ensure accurate and reliable test results, it is important to establish clear and specific test conditions. These conditions should include factors such as the environment, equipment used, and any other relevant variables that may impact the test outcome. By carefully defining these conditions, researchers can minimize the risk of errors or inconsistencies in the results. It is crucial to note that the test conditions should be standardized and consistent for all participants in the study to ensure fairness and validity of the study findings. Therefore, it is imperative to pay close attention to the details when designing the test conditions. While there are different approaches to generating content, it is recommended to avoid using ChapGPT or any similar software to ensure that the generated content is not similar to the original text. Instead, it is best to use language models or other methods of text generation that produce significantly different content.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of uncertainty arising from the verdict, certain tests shall be carried out under specific circumstances. It is important to ensure that the generated content is based on the original text information, but using a different language model to produce highly similar content instead of relying on ChapGPT.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2. ELECTRICAL SPECIFICATION
NO. | Items | Test conditions | Requirements |
2.2.1 | Contact | Small current measurements at 1kHz, such as 100mA or less, require careful consideration. To generate precisely similar content by rearranging the provided information, it is essential to address the specific requirements when measuring currents of such magnitude.
| 50mΩ MAX |
2.2.2 | Insulation | Apply a voltage of 1000VDC for 1 min. to following portions after which measurement shall be made. between terminals | 500MΩ MIN |
2.2.3 | Dielectric Strength
| AC 2000V RMS(50-60HZ)for 1 min trip between terminals.
| Without damage to parts Arcing or breakdown etc
|
2.3 MECHANICAL CHARACTERISTICS
2.3.1 | Operating force
| A static load shall be applied to the tip of actuator in operating direction | 3N |
2.3.2 | Operation Travel
| Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance.
| 2.6mm |
2.3.3 | Torque
| Applied to nut
| 5~14Nm |
2.3.4 | Panel Thickness
| Applied to nut
| 1~10mm |
2.3.5 | Life test
| Measurements shall be made following the test forth below： Ie:2A /Ue:36VDC .( resistive load) Rate of Operation:6-8operation cycles per minute. Electronics Life Test：50,000 cycles
| （1）Contact resistance: 100mΩmax. （2）（2）Insulation resistance 1000MΩ. （3）Dielectric strength：:1000VAC. （4）without damage to parts arcing or breakdown etc.
|
2.3.6 | Solder ability test
| The top of the terminals shall be dipped 2mm in the solder bath of 290±5℃ for 3±0.5 seconds.
| The area of soldering should be over 90%
|
2.4 ENDURANCE CHARACTERISTICS
| Life test
| Measurements shall be made following the test forth below： (1)3A 250/125VAC, 3A 30VDC (2)Electronics Life Test：10,000 cycles. (3)Mechanical Life Test：50,000 cycles
| (1）Meet the Criteria shown on item 2.3 （2)without damage to parts arcing or breakdown etc.
|
2.4.2 | Solder ability test
| The top of the terminals shall be dipped 2mm in the solder bath of 245±5℃ for 2±0.5 seconds.
| The area of soldering should be over 90%
|
3. DRAWING & DIMENSION
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
5.Remarks
PARTS LIST:
NO. | NO. | NAME | MATERIAL |
1 | 1 | Bushing | SUS304/Brass Ni plated/Al alloy |
2 | 1 | Base | PC |
3 | 1 | Actuator | PC/Stainless Steel |
4 | 1 | Contact | Ag ally |
5 | 1 | Terminal | H62 silver plated |
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: 12mm push button switch, China 12mm push button switch manufacturers, suppliers, factory