Technical parameters
2.1 General
This specification pertains to the utilization of Push Button Switch in electronic equipment. Kindly create a text that's highly comparable by rearranging the previous text, ensuring that the new content is founded on the original information. Please refrain from utilizing a dialogue format generated by ChapGPT, but instead generate a completely different text utilizing the language model.
2.1.2 Operating temperature range -20℃ ～ +55℃
In the absence of specific instructions, the tests and measurements should be conducted under specific atmospheric conditions. These conditions would be as follows . It is important that the content generated be similar to the original text but arranged in a different manner to meet the requirements of the task. Therefore, it is recommended to use a language model to generate text that is distinct from what has been seen so far in the original text.
Let's discuss the test conditions. To create a highly similar content, we need to rearrange the above information based on the original text. It's important to note that we should avoid using ChapGPT-generated content and instead, present an entirely distinct way of speaking by using language modeling to generate new text.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In the event of any uncertainty arising from the verdict, it is imperative to carry out tests under the designated circumstances.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
The appearance switch should be of excellent finishing, with no plating failures, rust, or cracks.
The product drawings provide detailed information regarding the construction and dimensions of each individual item. For accurate specifications, it is essential to refer to the specific product drawing.
2.3. ELECTRICAL SPECIFICATION
NO. | Items | Test conditions | Requirements |
2.3.1 | Contact | The content was measured at a frequency of 1kHz with a low current, not exceeding 100mA. To produce related content, the information given above can be rearranged. Please note that the generated speech should not follow the conversational style of ChapGPT, but instead provide a different approach using language modeling techniques.
| 30mΩ MAX |
2.3.2 | Insulation | Apply a voltage of 500VDC for 1 min. to following portions after which measurement shall be made. between terminals | 100MΩ MIN |
2.3.3 | Dielectric Strength
| AC 2000V RMS(50-60HZ)for 1 min trip between terminals.
| Without damage to parts Arcing or breakdown etc
|
2.4. ENVIRONMENT RESISTANCE:
NO. | Items | Test conditions | Requirements |
2.4.1 | Cold test
| The switch shall be stored at a temperature of -20±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| There shall be no deformation or cracks in Molded part.
|
2.4.2 | Heat resistance | The switch shall be stored at a temperature of 55±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| |
2.4.3 | Humidity test
| The switch shall be stored ata temperature of 40±2℃ and a humifity of 90% to 95% for 96 hours.then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made.
| |
2.4.4 | Standard conditions
| Unless otherwise specified. the standard range of atmospheric conditions for making measurements and tests are as follows: (1)Temperature:40±2℃ (2)Relative Humidity:90~95% (3)Time:96 hours.
|
2.5 MECHANICAL CHARACTERISTICS
2.5.1 | Operating force
| A static load shall be applied to the tip of actuator in operating direction | 10N±2N |
2.5.2 | Operation Travel
| Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance.
| 4.2 ±0.5mm |
2.5.3 | Terminal strength
| A static load of(500gf)shall be applied to the terminal for 15 sec,in any directon.
| Mechanical and electrical characteristics shall be satisfied without looseness of actuatou.
|
2.5.4 | Displacement of actuator (knob)
| A static load of 10n(1kgf)shall be applied to the top of the actuator(knob)and then desplacement shall be measured to the Direction of the arrow.
| The lever shall have no serious deformation and function is normally.
|
3. DRAWING & DIMENSION:
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
5.Remarks
PARTS LIST:
NO. | NO. | NAME | MATERIAL |
1 | 1 | Case,Housing | Nylon PA66 |
2 | 1 | Cover | Nylon PA66 or PC |
3 | 1 | Actuator | Nylon PA66 |
4 | 1 | Spring | Steel Wire |
5 | 1 | Lever ,Terminal | Copper Alloy |
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q:What about the lead time for mass production?
A:15-20 working days for mass production.It depends on your quantity,and we will try our best to meet your needs.
Q:Can l visit your factory?
A:By all means, we warmly welcome your arrival, Before you take off from your country, please let us know. We will show you the way and arrange time to pick you up if possible.
Hot Tags: pushbutton switch water resistance, China pushbutton switch water resistance manufacturers, suppliers, factory