Technical parameters

2.1 General
A toggle switch is primarily utilized as a switch for small electric currents and signals. Its main purpose is to control the flow of electricity within a circuit. This specification aims to provide a detailed description of this type of switch and its functionalities.

Please provide more specific information about the device you are referring to so that I can generate a highly similar content based on it. Thank you!
2.1.2 Operating temperature range -30℃ ～ +85℃
The specified atmospheric conditions for measurements and tests are as follows, unless stated otherwise. To ensure accuracy, it is important to adhere to these conditions
Let's discuss the conditions under which tests should be conducted. It's important to ensure that the testing conditions are appropriately controlled and representative of the intended usage scenario. Any environmental variables that may impact the test outcomes must be accounted for, and the testing equipment should be calibrated to ensure accuracy. Additionally, it's important to establish consistent testing procedures to minimize any potential variations in results. Please note that this is not the same as generating content using ChapGPT, but rather utilizing language modeling techniques to generate new content that is distinct from the original text.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any uncertainty regarding the verdict, examinations will be carried out under the circumstances mentioned below. Please create comparable content by reorganizing the preceding data, guaranteeing that the new information is consistent with the original text information.

2.2 Programmer of test:

PECULIARITY	ITEM	DESCRIPTION	TEST CONDITION	REQUIREMENTS
Electrical Characteristics	2.2.1	Visual Examination	Without applying any force or conducting experiments, carry out an analysis using visual means. Rearrange the words from the original passage to create a new sentence with a meaning that corresponds to the original text. Please note that this response is generated through a language model and differs significantly from ChapGPT-generated text.	The function of the product shall not be affected by any defects. I will generate highly similar content by reorganizing the provided information, ensuring that the generated content is based on the original text. Please note that the generated content may differ significantly from the original text as I will use a language model to create a different approach to the discussion. "The nonexistence of any defects that might impact the product's performance is essential. It is crucial to ensure that the functionality of the product remains unaffected by any flaws. Only when there are no defects can the product deliver its intended purpose efficiently. Therefore, it is imperative to thoroughly evaluate and rectify any potential issues before delivering the final product to the customers. By prioritizing defect-free products, we can guarantee user satisfaction and maintain the highest standards of quality."
	2.2.2	Contact Resistance	The measurement should be taken across the two terminals linked with every switch pole. Try generating a highly analogous text by rearranging the preceding text, while making sure it stays faithful to the original information. Please refrain from producing the text in the same way ChapGPT would generate it, and instead try a completely different approach using the language model to generate the text. To ensure accuracy, it is important to use a 1kHz current contact resistance meter when making measurements.	10mΩ 10mΩ MAX(initial)
	2.2.3	Insulation Resistance	500VDC,1min±5sec	1000MΩ MIN
	2.2.4	Dielectric withstanding voltage	1500VAC (50Hz or 60 Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute.	There shall be no breakdown or flashover
Mechanical Characteristics	2.2.5	Operating Force	Applied in direction operation ON→OFF OFF→ON	10N max
	2.2.6	Stop Strength	A static load of 30N is applied in the operating direction and pulling direction operated for a period of 30 seconds.	There shall be no sign of damage mechanically
	2.2.7	Soldering Heat Resistance	（1） Soldering Temperature：260±5°C （2）Duration of Solder Immersion：5±1 sec （3）Frequency of Soldering Process,2 times Max PCB is 1.6mm in thickness	As show in item2~6
Durability	2.2.8	Operation Life	Measurements shall be made following the test set forth below: 3A,250VAC resistive load Rate of Operation：6~8cycles/minute Cycle of Operation：6000cycles	As show in item 3.4
Endurance	2.2.9	Resistance Low Temperature	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Temperature：-30±3°C Time：48 hours	As show in item 2~6
	2.2.10	Resistance high Temperature	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Temperature：85±3°C Time：48 hours	As show in item 2~6
	2.2.11	Resistance Humidity	Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Temperature：40±2°C Relative Humidity：90-95% Time：48 hours	1.As show in item 4~6 2. Contact Resistance:100mΩ max 3.Insulation Resistance:10MΩ min

2.3.2 Manual soldering：

Soldering Temperature	MAX.350℃
Continuous Soldering Time	MAX.3 seconds

Precautions in Handling：

1.Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch.

2.Don’t wash switch body.

4. Product application

1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;    5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.

5.Remarks

PARTS LIST:

No.	Name	Material
1	Plastic Base	Nylon
2	ACTUATOR	Nylon Copper alloy，chrome plated with internal O-ring standard；Nylon
3	Plastic Enclosure	Nylon
4	END CONTACTS	Copper alloy, silver plated (Q contact material )
5	CENTER CONTACTS & ALL TERMINALS	Copper alloy, silver plated (Q contact material)
6	TERMINAL SEAL	Epoxy
7	Nut & Locking Ring	Brass，nickel plated
8	Lock washer	Steel

Returned plastic should not exceed 20%.

6.Delivery,shipping and service

TO6(0NMP4F[DWUIG7[DR~YI

7.FAQ

Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.

Q: Which payment form you can accept?

A: T/T, Western Union, PayPal etc. We accept any convenient and swift payment term.

Q: Can you provide the FBA shipping service?

A: Yes, we have the good experience in providing the professional FBA service.

Hot Tags: sealed toggle switch, China sealed toggle switch manufacturers, suppliers, factory

Sealed Toggle Switch