Technical parameters
2.1 General
The SK22D Slide Switch is a versatile component that is specifically designed for use in electronic equipment. Its applications are numerous, making it an essential part of various electronic devices. Whether it's used in consumer electronics, such as televisions or smartphones, or in industrial applications, like control panels or machinery, the SK22D Slide Switch consistently delivers reliable performance. Its compact size and durable construction make it suitable for a wide range of applications, ensuring that electronic equipment operates smoothly and efficiently.
2.1.2 Operating temperature range -16℃ ～ +60℃
In the absence of any specific instructions, the prevailing atmospheric conditions must be taken into account during the process of measurement and testing. The following conditions are to be maintained throughout the duration of the procedure.
，，。，ChapGPT，。
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any uncertainty arising from the decision, it may be necessary to carry out further tests under specific conditions. The aim is to clarify any doubts and ensure that the judgment is based on accurate and reliable information.
2.3 Operating Characteristics:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.3.1 | OPERATING FORCE | The measurement should be taken at the closest point of the component or at a point 3mm away from the tip of the actuator (knob) which is elevated by 5mm. | 200gf±80gf |
2.3.2 | TERMINAL STRENGTH | In any direction, the tip of the terminal should be subjected to a static load of 300gf for a duration of 1 minute. Please ensure that the generated content closely resembles the original text while rearranging the information. | ELECTRICAL Satisfaction shall be guaranteed without any damage or loss, with the fulfillment of the specified characteristics. EXCESSIVE LOOSENESSOF ACTRATOR. |
2.3.3 | DISPLACEMENT OF ACTUATOR（KNOB） | -10℃～+60℃. UNLESS OTHERWISE SPECIFIED.THE STANDARD RANGE OF ATMOSPHRIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1)AMBIENT TEMPERATURE:5℃TO35℃ (2)RELATIVE HUMIDITY:45%TO85% (3)AIR PRESSURE:80Kpa TO 106Kpa | THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. |
2.4 Electrical Specification:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.4.1 | CONTACT RESISTANCE | MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS) | 70mΩ MAX |
2.4.2 | INSULATION RESISTANCE | APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER WHICH MEASUREMENT BE MADE: (1) BETWEEN TERMINAL. (2) BETWEEN INDIVIDUAL TERMINAL AND FRAME. | 100MΩ MIN |
2.4.3 | DIELECTRIC STRENGTH | AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA (1) BETWEEN TERMINAL. (2) BETWEEN INDIVIDUAL TERMINAL AND FRAME. | WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. |
2.5 Environment Resistance:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.5.1 | HUMIDITY TEST | THE JACK SHALL BE STORED AT A TEMPERATURE OF 40±2 °C AND A HUMIDITY OF 90% TO 95% FOR 96 Hr . THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES. | THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.
|
2.5.2 | STANDARD ATMOSPHERIC CONDITIONS | UNLESS OTHERWISE SPECIFIED. THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1) AMBIENT TEMPERATURE : 5 °C TO 35 °C (2) RELATIVE HUMIDITY : 45% TO 85% (3) AIR PRESSURE : 86Kpa TO 106Kpa | |
2.5.3 | PRACTICAL TEMPERATURE RANG | -16 °C ~ +60 °C |
2.6 Endurance
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.6.1 | LIFE TEST | WITHOUT LOAD: AN ACTUATOR SHALL BE SUBJECT TO 5,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN. | (1)CONTACT ERSISTANCE SHALL BE 200mΩMAX. (2)MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
THERE SHALL BE NO DAMAGE ONAPPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALLBE SATISFIED. |
2.6.2 | RESISTANCE TO SOLDERING HEAT TEST | THE SWITCH SHALL BE STORED AT A TEMPERATURE OF 80±2℃ FOR 96 HOURS.AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.
| |
2.6.3 | HEAT TEST | THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -20±3℃ FOR 96 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE | |
2.6.4 | COLD TEST | THE SWITCH SHALL BE STORED ATA TEMPERATURE OF 40±2℃ AND A HUMIFITY OF 90% TO 96% FOR 96 HOURS .THEN THE SWITCH SHALL BE MAINTAINED ATST ANDARD ATMOSPHERIC CONDITION FOR. |
3.Drawing & Dimension:
4. Circuiy Diagram:
5.Product application
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
6.Remarks
PARTS LIST:
ITEM | PARTS | MATERIALS | QUANTITY | FINISH |
1 | KNOB | PA6T | 1 | BLACK |
2 | COVER | SUS | 1 | NATURAL |
3 | CASE | PA6T/BRASS STRIP | 1 | BLACK/Ag PLATED |
4 | CONTACT | PBS WIRE | 2 | NATURAL |
Returned plastic should not exceed 20%.
7.Delivery,shipping and service
8.FAQ
Q：What is the delivery time for mass production?
A:About 25 days.
Q：Can I request to advance the shipment?
A: It should be depends on whether there is sufficient inventory in our warehouse.
Q：How long can I expect to get the sample?
A:3-5 working days for samples.
Hot Tags: 6 pin slide switch, China 6 pin slide switch manufacturers, suppliers, factory