Technical parameters
2.1 General
:1MD6，。
2.1.2 Operating temperature range -30℃ ～ +85℃
If not stated otherwise, the measurements and tests are to be conducted under the specified atmospheric conditions.
Let us discuss the test conditions that would be required for conducting a successful experiment. It is important to note that we need to generate content that is highly similar to the original text. However, the content should be rearranged in a way that reflects the key information of the original text. This is important as it allows us to explore different perspectives on the same topic. It is advisable to refrain from using the ChapGPT method of generating content, but instead, use other language modeling techniques to create a text that is completely different from the original. This will enable us to achieve greater depth and accuracy in our discussions.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any uncertainty arising from the decision, certain tests must be carried out under specific conditions. It is essential to follow these guidelines to ensure that the tests and subsequent judgments are accurate and reliable.
2.2 Environment Resistance
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.2.1 | Humid test | ，40 + 2 ℃，90-95%。96，1。，。 | The mechanical and electrical properties are in accordance with normal expectations, with no unusual physical characteristics observed. |
2.2.2 | Test standard state | To gather data for testing, we will measure the temperature, humidity, and air pressure in the given scenario. It is important to ensure that the specified case is absent in order to conduct unbiased experiments. By rearranging the content provided, we can proceed with generating a highly similar context while maintaining the original information. （1） temperature： 5~35°C 。 （2） humidity： 45~85% 。 （3） pressure： 86Kpa~106Kpa 。
| |
2.2.3 | Use of temperature range | It is used at -306 C ~ +85 ℃ temperature. |
2.3 Endurance
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.3.1 | Life Test | Measurement under the following test: （1） 5A 120VAC Resistive load - Plate with silver 2A 250VAC Resistive load - Plate with silver 0.4A 20VAC Resistive load - Plate with gold （2）Operating frequency：The frequency of 6-8 times per minute （3）Electrical life 6,000 make-and-break cycles. （4）Mechanical life 40,000 make-and-break cycles. | (1) contact resistance：10 mΩ MAX (2) insulation resistance： 1000 MΩ MIN (3) Insulation strength：1000V (4) After testing, the appearance is free from damage and meets mechanical properties. |
2.3.2 | Weldability test | The top of the terminal is immersed in the 2mm depth of the solder pool, the temperature is 230 + 5℃, and the time is 3 + 0.5 seconds. | The welding area should be more than 75%. |
2.3.3 | Solderability test | When hand welding, the temperature is controlled at 350 + 10 degrees, and the time is 3 + 0.5 seconds. However, abnormal pressure can not be applied to the feet. | There is no abnormal appearance, which is satisfied with mechanical and electrical properties. |
2.3.4 | Heat resistance test | It was placed at a temperature of 85 + 2℃, and then placed at normal room temperature for 1 hours after 96 hours. | |
2.3.5 | Cold tolerance test | It was placed at a temperature of -40 + 3℃, and then placed in normal room temperature for 1 hours after 96 hours. |
2.7 Storage Method:
(1) IF DON'T USE THE PRODUCT IMMEDIATELY,STORE IT AS DELIVERED IN
THE FOLLOWING ENVIRONMENT: WITH NEITHER DIRECT SUNSHINE NOR
CORROSIVE GAS AND IN NORMAL TEMPERATURES. HOWEVER, IT IS
RECOMMENDED THAT YOU SHOULD USE IT AS SOON AS POSSIBLE BEFORE
SIX MONTHS PASS.
(2) AFTER BREAK THE SEAL，IT SHOULD PUT THE REMAINING IN A
PLASTIC BAG TO SEPARATE IT FROM THE OUTSIDE AND STORE IN THE
SAME ENVIRONMENT MENTIONED ABOVE. YOU SHOULD USE IT UP AS
SOON AS POSSIBLE.
(3) DO NOT STACK TOO MANY SWITCHES FOR STRAFE.
3.Drawing & Dimension:
4. Circuiy Diagram:
6.Remarks
PARTS LIST:
NO | quantity | name | Material Science |
1 | 1 | Case | Phthalate(DAP)(UL94V-0) |
2 | 1 | Actuator | Brass, chrome plated. |
3 | 1 | Bushing | Brass, nickel plated. |
4 | 1 | Housing | Stainless Steel. |
5 | 6 | Contact /Terminal | Brass, gold plated |
Returned plastic should not exceed 20%.
8.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: dpdt momentary toggle switch, China dpdt momentary toggle switch manufacturers, suppliers, factory