Technical parameters
2.1 General
2.1.1 Application: The 6012 Toggle Switch is specifically designed for use in electronic equipment. It is intended to be employed as a reliable and efficient component in various electronic devices. The primary objective of this specification is to define the specific usage and purpose of the 6012 Toggle Switch in the context of electronic equipment. By adhering to these guidelines, manufacturers and users can ensure seamless integration and optimal performance of the switch within their electronic systems.
2.1.2 Operating temperature range 0℃ ～ +105℃
The specified atmospheric conditions for measurements and tests are as follows unless stated otherwise. It is important to ensure that the generated content is based on the original text information, but presented in a completely different manner.
Let's discuss the test conditions for our project. It's important to ensure that we have a highly controlled environment for our testing. This will help ensure the reliability and validity of our data. We need to consider the variables that may impact our results, such as temperature, humidity, lighting, and equipment calibration. Therefore, we should carefully monitor and document the conditions under which we are conducting our tests. It's also important to maintain consistency throughout our testing, and to verify that our results are repeatable. Let's keep these factors in mind as we move forward with our project.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
Tests may be conducted under the following conditions if there is any uncertainty arising from the judgement. It is important to ensure that the testing process is conducted to provide conclusive evidence regarding the matter in question. By following a rigorous testing protocol, it is possible to arrive at a clear and accurate conclusion that can be relied upon. Therefore, it is essential to conduct rigorous tests that adhere to strict standards and guidelines. This can help to ensure that all relevant information is considered and that the decision arrived at is well-informed and based on a thorough understanding of the situation.
2.3 Mechanical Properties
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.3.1 | Operating Force | The static load at the front of the operation section was measured to be between 1000 and -500 gf along the direction of operation. Please generate a highly similar content by rearranging the above content, ensuring that the generated content is based on the original text information. | According to the Recognition Chart |
2.3.2 | Terminal Strength | A strength test with a force of (1000gf) will take a minute in any square type located in the front row of feet. Can you produce a similar content, but rephrased while still reflecting the information from the original text? Please avoid using the same method as ChapGPT to generate the content, opting instead for a completely different approach using language models. | The terminals show no signs of cracks or abnormalities that would affect their mechanical and electrical properties. There is no evidence of loosening or any other issues that could impact their functionality. |
2.3.3 | Solder adhesion | Confirmation after testing under the following conditions： soldering temperature：270℃ immersion time：3±0.5 seconds Dip flux in room temperature for 5-10 seconds | 90% of the immersed part must be tin-coated |
2.3.4 | Solder resistance | Confirmation after testing under the following conditions： soldering temperatureimmersion timeManual solder365~370℃2~3 secondsAutomatic solder270+2℃10±1 seconds | There is no serious distortion in appearance, and it can work normally. |
2.4 Electrical Specification:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.4.1 | Contact resistance | The 2-4VDC is tested under tiny current (below 100mA), silver plated or gold plated. | 20mΩ MAX |
2.4.2 | Insulation resistance | Input 500V DC voltage for 1 minutes, test according to the following contact mode: （1）Between the terminal. （2）Between the terminal and the outer shell. | 100MΩ MIN |
2.4.3 | Pressure resistance | Measurement of AC 1500V (50-60 Hz) between open contacts and poles Measurement of AC 3000V (50~60Hz) between terminal and grounding Fixed time: 1 minute each | No abnormalities such as insulation damage |
2.7 Storage Method:
（1）If the product is not used immediately, it should be kept at normal temperature without direct sunlight and corrosive gases.
In the environment. But we recommend that we use it as soon as 6 months.
（2）Put the finished products in plastic bags and seal them in the same environment as soon as possible, and use them as soon as possible. Do not overlay excess when saved in order to prevent the pressure from breaking.
（3）Do not overlay excess when saved in order to prevent the pressure from breaking.
3.Drawing & Dimension
5.Product application
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
6.Remarks
PARTS LIST:
NO. | PART NAME | MATERIAL |
1 | NUT | STEEL Ni PLATED |
2 | WASHER | STEEL Zn PLATED |
3 | LOCKING WASHER | STEEL Zn PLATED |
4 | BUSHING | BRASS Ni PLATED |
5 | BRACKET | STEEL Zn PLATED |
6 | TOGGLE HANDLE | BRASS Cr PLATED |
7 | COVER | NYLON 66 GLASS REINFORCED |
8 | HOLDER OF TIP | POLYBUTYLENE TEREPHTHALATE(PBTP) GLASS REINFORCED |
9 | SPRING | PIANO WIRE OIL |
10 | TIP | MELAMINE/PHENOLIC |
11 | ARM | COPPER Ag PLATED |
12 | MOVABLE CONTACT | Ag ALLOY |
13 | STATIONARY CONTACT | Ag ALLOY |
14 | TERMINAL | COPPER Ag PLATED |
15 | BODY | PHENOLIC |
16 | LABEL | PVC |
Returned plastic should not exceed 20%.
7.Delivery,shipping and service
8.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: on on toggle switch, China on on toggle switch manufacturers, suppliers, factory