Technical parameters
2.1 General
The 1MD6 Toggle Switch finds application in electronic equipments. This specification pertains to the said toggle switch. To create a similar content, the given information needs to be rearranged while retaining its essence. The 1MD6 Toggle Switch is utilized in electronic devices as per this specification.
2.1.2 Operating temperature range -30℃ ～ +85℃
If not specifically stated otherwise, the parameters for conducting tests and taking measurements should be executed under certain atmospheric conditions, which are listed as follows. Please note that the generated content is based on the original text information but expressed differently.
Let's discuss the conditions for testing. To create a new text that closely reflects the original information, we should rearrange the content with care. Please note that we should avoid using ChapGPT to generate content for this purpose. Instead, we should rely on a language model to produce text that is significantly different from the original.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In the event of any uncertainty regarding the decision, assessments will be carried out under specific circumstances. It is important to reiterate that the generated content should not be based on the ChapGPT dialogue generation method, rather, language models should be utilized to generate completely different text.
2.3 Operating Characteristics:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.3.1 | Operating Force | The rubber handle is located 3mm away from the test point. The test is then conducted three times. To generate highly similar content based on the original text information, please rearrange the above content. | 200gf±100gf |
2.3.2 | Terminal Strength | The time required for a strength test of (500gf) plus any square type in the front row of feet is 15 seconds. Please generate a content that is highly similar by rearranging the given information. | The terminals must possess both mechanical and electrical properties without any cracks, looseness, or other anomalies. |
2.3.3 | Shank strength | The force of 1Kgf is applied at the front of the handle, and the displacement should be fixed along the direction of the mark. | There is no serious deformation of the handle, and it can work normally. |
2.4 Electrical Specification:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.4.1 | CONTACT RESISTANCE | The 2-4VDC is tested under tiny current (below 100mA), silver plated or gold plated. | 10mΩ MAX |
2.4.2 | INSULATION RESISTANCE | Input 500V DC voltage for 1 minutes, test according to the following contact mode: （1）Between the terminal. （2）Between the terminal and the outer shell. | 1000MΩ MIN |
2.4.3 | Pressure resistance | Input 1000V DC voltage for 1 minutes, test according to the following contact mode: （1）Between the terminal and the outer shell. | No abnormality, such as insulation damage |
2.5 Environment Resistance:
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.5.1 | Humid test | It was placed in a temperature of 40 + 2 ℃ and a relative humidity of 90~95%. After 96 hours, it was placed at normal room temperature for 1 hours. | No abnormal appearance，Meet the mechanical and electrical properties。 |
2.5.2 | Test standard state | In the absence of a specified case Test the temperature, humidity, and air pressure as follows： （1） temperature： 5~35°C 。 （2） humidity： 45~85% 。 （3） pressure： 86Kpa~106Kpa 。
| |
2.5.3 | Use of temperature range | It is used at -306 C ~ +85 ℃ temperature. |
2.6 Endurance
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.6.1 | Life Test | Measurement under the following test: （1） 5A 120VAC Resistive load - Plate with silver 2A 250VAC Resistive load - Plate with silver 0.4A 20VAC Resistive load - Plate with gold （2）Operating frequency：The frequency of 6-8 times per minute （3）Electrical life 6,000 make-and-break cycles. （4）Mechanical life 40,000 make-and-break cycles. | (1) contact resistance：10 mΩ MAX (2) insulation resistance： 1000 MΩ MIN (3) Insulation strength：1000V (4) After testing, the appearance is free from damage and meets mechanical properties. |
2.6.2 | Weldability test | The top of the terminal is immersed in the 2mm depth of the solder pool, the temperature is 230 + 5℃, and the time is 3 + 0.5 seconds. | The welding area should be more than 75%. |
2.6.3 | Solderability test | When hand welding, the temperature is controlled at 350 + 10 degrees, and the time is 3 + 0.5 seconds. However, abnormal pressure can not be applied to the feet. | There is no abnormal appearance, which is satisfied with mechanical and electrical properties. |
2.6.4 | Heat resistance test | It was placed at a temperature of 85 + 2℃, and then placed at normal room temperature for 1 hours after 96 hours. | |
2.6.5 | Cold tolerance test | It was placed at a temperature of -40 + 3℃, and then placed in normal room temperature for 1 hours after 96 hours. |
2.7 Storage Method:
(1) IF DON'T USE THE PRODUCT IMMEDIATELY,STORE IT AS DELIVERED IN
THE FOLLOWING ENVIRONMENT: WITH NEITHER DIRECT SUNSHINE NOR
CORROSIVE GAS AND IN NORMAL TEMPERATURES. HOWEVER, IT IS
RECOMMENDED THAT YOU SHOULD USE IT AS SOON AS POSSIBLE BEFORE
SIX MONTHS PASS.
(2) AFTER BREAK THE SEAL，IT SHOULD PUT THE REMAINING IN A
PLASTIC BAG TO SEPARATE IT FROM THE OUTSIDE AND STORE IN THE
SAME ENVIRONMENT MENTIONED ABOVE. YOU SHOULD USE IT UP AS
SOON AS POSSIBLE.
(3) DO NOT STACK TOO MANY SWITCHES FOR STRAFE.
3.Drawing & Dimension:
4. Circuiy Diagram
5.Product application
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on; 5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
6.Remarks
PARTS LIST:
NO | quantity | name | Material Science |
1 | 1 | Case | Phthalate(DAP)(UL94V-0) |
2 | 1 | Actuator | Brass, chrome plated. |
3 | 1 | Bushing | Brass, nickel plated. |
4 | 1 | Housing | Stainless Steel. |
5 | 6 | Contact /Terminal | Brass, gold plated |
Returned plastic should not exceed 20%.
7.Delivery,shipping and service
8.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: on on on toggle switch, China on on on toggle switch manufacturers, suppliers, factory