1.General

The KW10 Micro Switch used for electronic equipment is subject to the application of this specification. This means that all aspects of the micro switch, including its design, performance, and features, must comply with the requirements outlined in this document. By adhering to the specifications, the micro switch can effectively function within electronic devices and ensure reliable operation. It is crucial to generate a highly similar content by rearranging the original information to accurately reflect the purpose and usage of the KW10 Micro Switch in electronic equipment.
1.2 Operating temperature range -40℃ ～ +85℃
In the absence of specific instructions, the following are the atmospheric conditions to be maintained during measurements and tests. Could you please reformulate the given content using a different approach, making sure that the generated text is based on the original information?
1.4 Test conditions
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case any questions or uncertainties arise regarding the judgement, it is necessary to conduct tests under the specified conditions.
Ambient temperature: 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)

2.Appearance construction and dimensions
The Appearance Switch should exhibit excellent finishing, with no signs of rust, cracks, or plating failures.
When it comes to construction and dimensions, it's important to refer to each product drawing individually. This will provide you with the specific details you need to ensure you are getting the right product for your needs. By looking at these drawings, you can see exactly how the product is constructed and what its dimensions are. This information is crucial in determining whether or not a product will work for you and any specific requirements you may have. So, be sure to take the time to carefully examine the product drawings to make sure you are getting the right information.

3.Operating Characteristics:

Characteristics	Units	Standards	Note
Actuating Force	N	0.5 Max	Original 0.5 max.
Release Force	N	0.05 Min	Original 0.05 Min
Over travel	mm	0.6 Min	Original 0.6 Min
Movement differential travel	mm	0.6 Max	Original 0.6 Max.
Operating Position	mm	8.5±1.0mm	Original 8.5±1.0 mm

Note:

Actuating Force:

To move the actuator from its free position, a certain amount of force is needed. This force may vary depending on the specific actuator and the conditions under which it is being used. However, in general, it is important to determine the force required in order to properly operate the actuator and ensure that it is functioning efficiently. Factors such as friction, load capacity, and operating temperature may all play a role in determining the optimal force needed for proper actuator performance. Therefore, it is important to carefully assess these factors and adjust the force accordingly to achieve the best possible results.
the operation position

Release Force

After the actuator was reset, the force was still present in the mechanism. To create similar content based on this information, one could say "Even after the actuator was reset, the force remained active in the mechanism."
operation

Free Position

The actuator's position when there is no external force acting upon it. To create a substantially similar content, the information in the original text is expressed using different words and sentence structures.

Operating Position

When the contact change-over occurs, the actuator's position is crucial. To reiterate, it is important to note that the actuator's position plays a key role in the contact change-over process. Therefore, it is imperative to ensure that the actuator is in the right position when the contact change-over takes place.
place

Movement Differential

The separation between the position where the operation takes place and the position where the release occurs is of utmost importance. To create similar content, this can be rephrased as follows: The space between where the procedure is performed and where the discharge happens is a critical factor.

4 Electrical Specification:

NO.	Items	Test conditions	Requirements
4.1	Contact Resistance	After performing certain operations, the measurement shall be conducted using the voltage drop method at a 1A, 5V DC. It is crucial to rearrange the provided content and ensure that the generated content maintains the information from the original text. without load. : CNO。，，。	50mΩ MAX
4.2	Insulation Resistance	Test voltage:500VDC, measured after 1 min ±5s Applied Position: applied position: 1)Between terminal “C” and terminal “NO” 2)Between terminal and ground	100MΩ MIN
4.3	Voltage proof	To conduct testing, the specified test voltages must be applied for a duration of one minute. In order to remain true to the original information provided, the generated content will rearrange the structure of the sentence without altering its meaning. The voltage between terminal "C" and terminal "NO" is 600VAC at a frequency of 50 to 60Hz. Can you produce an analogous text by rearranging the given information such that the meaning remains the same? Please remember to generate the content using a language model, rather than relying on ChapGPT's dialogue generation technique. 2)Between terminal and ground: 1000V AC(50~60Hz)	No dielectric breakdown shall occur

5.Welding Performance:

5.1

Solder ability

，。，。

1)Variable temperature range :235±5℃;

2)Dip time:3±0.5s;

The area of dip tin should capture the 95% impregnated area

5.2

Resistance to soldering heat

The switch will be inspect under such conditions below

Temperature and impregnated time

All of the appearance, motor functions, electrical properties are no abnormal.

Drawing & Dimension:

Circuiy Diagram:

FAQ

Q:Can you give me a discount?
A: Discount is available,but we have to see the real quantity,we have different price based on different quantity,how much discounts is determined by the quantity,moreover,our price is very competitive in the field

Q:Have your products been exported?
A: Yes, they have been exported to USA, Canada, Australia, Russia,Chile,Panama,Nicaragua, UAE, Saudi Arabia,Egypt,Sri Lanka, Nigeria, Iran,Vietnam,

Indonisia,Singapore,Greece,Netherland,Georgia,Romania,Ireland, India, Thailand, Pakistan, Philippines, Singapore, HK,Taiwan...

Q: Do you have the test and audit service?

A: Yes, we can assist to get the designated test report for product and the designated factory audit report.

Q:How long can I expect to get the sample?

A:After you pay the sample charge and send us confirmed files, the samples will be ready

for delivery in 1-3 days. The samples will be sent to you via express and arrive in 3-5 days.

Hot Tags: gold plated miniature switch, China gold plated miniature switch manufacturers, suppliers, factory

Gold Plated Miniature Switch