Technical parameters
2.1 General
The KW10 Micro Switch is designed for electronic equipment and this specification applies to its usage. To provide a highly similar content based on the original information, the following content is generated.
2.1.2 Operating temperature range -25℃ ～ +125℃
The prescribed conditions for conducting tests and measurements, unless specified otherwise, are to be considered under the following atmospheric circumstances . To produce an alternate version, utilize a language model to generate new content that differs significantly from the original text.
2.3 Note：
Actuating Force:
Moving the actuator from the free state to . to ensure a smooth transition, a certain force is necessary.
the operation position
Release Force
After the mechanism reset, the force enabled the actuator to function again.
operation
Free Position
The actuator's resting position is the position it assumes when there is no external force acting upon it. To create a highly similar content, one can simply rephrase the above statement by saying, "The actuator remains in its default position when there is no external force exerted on it." This statement carries the same message as the original one, albeit with a different choice of words.
Operating Position
When contact change-over occurs, the actuator's position is important. There is a need to generate highly similar content that is based on the original text information but with a rearranged structure. Using a language model, the content will be presented in a different manner.
place
Movement Differential
The space that separates the position of operation and release must be taken into account. To produce text that closely follows the original content, the content can be rearranged without changing the meaning of the message. However, instead of using the ChapGPT method, a different language model can be utilized to generate highly similar content that is distinct from the original.
2.4 Durability:
NO. | Item | Test conditions | Criteria |
2.5.1 | Cold | Following the completion of a 96-hour testing period at -25±2℃, the switch must undergo a subsequent one-hour pause under normal room temperature and humidity conditions before measurements can be taken. It is imperative that any water droplets are eliminated prior to the measurement process. | Contact resistance(item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Variations in the operating characteristics are allowed within a range of ±10% of the specified value. This means that the equipment can perform slightly above or below the stated parameters, as long as it remains within this range. In both appearance and construction, any deviations shall not be acknowledged as normal. |
2.5.2 | Dry heat | After testing at 125±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. | |
2.5.3 | Damp heat | After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | |
2.5.4 | Change of temperature | After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
2.5 Welding Performance:
2.6.1 |
Solder ability | Switch test under such conditions and inspect after. 1）Variable temperature range ：235±5℃； 2）Dip time：3±0.5s； |
The area of dip tin should capture the 95% impregnated area |
2.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time Trial measuretemperature（℃）Time（s）Slot welding method260±55±1Soldering method350±53±0.5
|
All of the appearance, motor functions, electrical properties are no abnormal. |
3.Drawing & Dimension:
4. Circuiy Diagram:
5.Remarks
PARTS LIST:
NO. | Items | Material |
1 | Stopper | Brass alloy H65 |
2 | Case | Plastic PBT |
3 | NO terminal | Brass alloy H65, Sliver plated |
4 | Terminal | Brass alloy H65, Sliver plated |
5 | Cover | Plastic PBT |
6 | Plunger | Plastic PPS |
7 | Moving piece | Beryllium bronze |
8 | Spring sheet | Beryllium bronze |
9 | Moving arm | Stainless steel SUS304 |
10 | Contact | AgNi10 |
11 | Contact | AgNi10 |
Returned plastic should not exceed 20%.
6. Advantages
1. Our professional R&D and QC team can strictly control the product quality to meet your requirement.
2 We offer the best service according to your request, ranging from production, processing to packaging, etc.
3. Our products are of high quality at cheap price, and delivered on time.
4. We have a professional sales team to provide you quick and warm service throughout the whole process.
5. Small quantity is acceptable.
7.FAQ
Q:What’s the payment terms?
A:T.T with 30% downpayment,70%before shipment.or L/C at sight.Paypal or West Union also accept.
Q: Can you provide the FBA shipping service?
A: Yes, we have the good experience in providing the professional FBA service.
Q:What about the lead time for mass production?
A:15-20 working days for mass production.It depends on your quantity,and we will try our best to meet your needs.
Hot Tags: 5a 250vac micro switch, China 5a 250vac micro switch manufacturers, suppliers, factory