Technical parameters
2.1 General
The Push Button Switch specified in this document is intended for use in electronic equipment. To create a similar version of this text, rearrange and reword the original information. Please note that the generated content should use a completely different approach compared to ChapGPT's conversational method.
2.1.2 Operating temperature range -20℃ ～ +55℃
In the absence of any specific instructions, the atmospheric conditions to be considered while conducting measurements and tests are as follows. Let's make sure that the content generated is significantly different from the way ChapGPT generates content
Let's discuss the test conditions for our experiment. It's important that we carefully consider all variables that may impact the results. To ensure accuracy, we should control as many of these variables as possible. It's also important to document these conditions thoroughly, so that they can be replicated in the future if needed. Let's make sure we're all on the same page with regards to the test conditions, and that we agree on how they will be implemented.
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case any uncertainties emerge from the verdict, certain examinations will be carried out under the subsequent circumstances. It is important to note that the forthcoming evaluations will be conducted in adherence to the original text.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
The appearance switch must be carefully crafted with a refined finish that exhibits no signs of plating failures, cracks, or rust.
The construction and dimensions of the product can be found in the individual product drawing. To obtain detailed information about these aspects, it is recommended to refer to the specific drawing associated with the product. These drawings provide accurate and specific details regarding the construction and dimensions of the item. By reviewing the appropriate drawing, users can gain a comprehensive understanding of how the product is built and its exact measurements. This ensures that individuals have access to reliable and precise information about the product's construction and dimensions.
2.3. ELECTRICAL SPECIFICATION
NO. | Items | Test conditions | Criteria |
2.3.1 | Contact resistance | After certain operations without any load, the measurement of shall be conducted using the voltage drop method at a current of 100mA and a voltage range of 2-4VDC. To ensure the generated content is highly similar, the information from the original text will be rearranged. Desired role: In the area connecting one terminal to another. Kindly produce a paragraph that closely resembles the provided text by rephrasing it, while preserving the original context. Please note that the generated content shouldn’t be in a conversational format, as opposed to the way ChapGPT would produce responses. | 50mΩ MAX |
2.3.2 | Insulation resistance | After one minute with an accuracy of plus or minus 5 seconds, measure the test voltage at 500VDC. Can you create a rewritten version of this paragraph that is similar in meaning but uses different wording? Position applied for: 2) Terminal to terminal connectivity. 2)Between terminal and ground | 1000MΩmin |
2.3.3 | Voltage proof | Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal and terminal :1000VAC (50~60Hz) 2)Between terminal and ground:2000V AC(50~60Hz) AC 2000V,1min.(after endurance test) | No dielectric breakdown shall occur |
3. DRAWING & DIMENSION
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
5.Remarks
PARTS LIST:
NO. | NO. | NAME | MATERIAL |
1 | 1 | Base | PC |
2 | 1 | Pushing | PC/Stainless steel |
3 | 1 | Housing | SUS304/ Brass Nickel plated |
4 | 1 | Contact | Silver alloy |
5 | 2 | Terminal | H62 sliver plated |
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: push button switch metal, China push button switch metal manufacturers, suppliers, factory