Technical parameters
2.1 General
We will now discuss the intended application of the Push Button Switch. This type of switch is commonly used in electronic equipment. Therefore, this specification will be used to ensure that the Push Button Switch meets the necessary requirements for its intended use. By adhering to this specification, we can ensure that the Push Button Switch will function properly in electronic equipment.
2.1.2 Operating temperature range -20℃ ～ +55℃
The specified atmospheric conditions for conducting measurements and tests are as follows, unless stated otherwise. It is important to ensure that the generated content is based on the original text information. However, please refrain from using the conversational method employed by ChapGPT and instead generate content using a significantly different approach using a language model.
。，。
，：
1. ：，、、。
2. ：，、、。
3. ：，。
4. ：，。
5. ：，、。
6. ：，、。
7. ：，、。
8. ：，、。
，，。，。
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case doubts arise from the judgment, it is necessary to conduct tests under the conditions specified below.
Ambient temperature： 20±2℃
Relative humidity 60~70%
Air pressure 86~106kPa (860~1060 mbar)
2.2 Appearance construction and dimensions
The Appearance Switch should possess excellent finishing, free from any signs of rust, cracks, or plating failures. Let's ensure that the generated content is closely related to the original text information.
When it comes to construction and dimensions, it's important to refer to the individual product drawing for accurate specifications. Any variations in these factors can greatly impact the performance and functionality of the product, so it's important to get them right. Take the time to carefully review the information provided and make sure that all dimensions and construction materials are in line with what is required. By doing so, you can ensure that the product will meet your needs and perform as expected.
2.3. ELECTRICAL SPECIFICATION
NO. | Items | Test conditions | Requirements |
2.3.1 | Contact | 1kHz，（100mA）。，，。
| 50mΩ MAX |
2.3.2 | Insulation | To ensure accurate measurements, it is necessary to apply a potential of 1000 V/DC and a current of 100mA across the terminals and cover. This potential should be maintained for a duration of 1 minute. The measurements should be conducted according to this specific procedure. By following these instructions precisely, reliable and consistent results can be obtained.
| 1000MΩ min.
|
2.3.3 | Dielectric Strength
| AC 2000V RMS(50-60HZ)for 1 min trip between terminals.
| Without damage to parts Arcing or breakdown etc
|
2.4. ENVIRONMENT RESISTANCE:
NO. | Items | Test conditions | Requirements |
2.4.1 | Cold test
| The switch shall be stored at a temperature of -20±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| There shall be no deformation or cracks in Molded part.
|
2.4.2 | Heat resistance | The switch shall be stored at a temperature of 55±3℃ for 96 hours. Then the switch shall be maintained at standard atmospheric conditions for 1 hour after which measurement shall be made.
| |
2.4.3 | Humidity test
| The switch shall be stored ata temperature of 40±2℃ and a humifity of 90% to 95% for 96 hours.then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made.
| |
2.4.4 | Standard conditions
| Unless otherwise specified. the standard range of atmospheric conditions for making measurements and tests are as follows: (1)Temperature:40±2℃ (2)Relative Humidity:90~95% (3)Time:96 hours.
|
2.5 MECHANICAL CHARACTERISTICS
2.5.1 | Operating force
| A static load shall be applied to the tip of actuator in operating direction.
| 3N Max. |
2.5.2 | Operation Travel
| Switch at the vertical operating orientation placement, with a force equal to 2 times according to the static load applied on the switch button the top center, measure the top moving distance.
| 3mm |
2.5.3 | Torque
| Applied to nut
| 5~14Nm |
2.5.4 | Panel Thickness
| Applied to nut
| ≤12mm |
2.6 ENDURANCE CHARACTERISTICS
| Life test
| Measurements shall be made following the test forth below： Ie:3A /Ue:250VAC .( resistive load) Rate of Operation: 6-8operation cycles per minute. Electronics Life Test： 50,000 cycles.(for 3A/250VAC) Electronics Life Test： 6,000 cycles.(for 3A/28VDC) (5)Electronics Life Test： 6,000 cycles.(for 0.2A/110VDC)
| 1）Contact resistance 100mΩmax.（2）Insulation resistance 1000MΩ. （3）Dielectric strength：:1000VAC. （4）without damage to parts arcing or breakdown etc.
|
2.6.2 | Solder ability test
| The top of the terminals shall be dipped 2mm in the solder bath of 260±5℃ for 3±0.5 seconds.
| The area of soldering should be over 90%
|
3. DRAWING & DIMENSION:
4.Product application
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
5.Delivery,shipping and service
6.FAQ
Q：Do you have after-sale service?
A:Yes, Good after-sale service, handling the customer complaint and solve problem for customers.
Q：How to solve the equipment trouble during using ?
A: Please email us about problem with pictures or a small video will be better,we will find the problem and solve it. If broken, we will send you a new free part if in the warranty period.
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: metal pushbutton switch, China metal pushbutton switch manufacturers, suppliers, factory