Technical parameters
2.1 General
2.3 Operating Characteristics:
Characteristics | Units | Standards | Note |
| N | 4±1.5 Max | Original 4±1.5 . |
Contact Force | N | 0.4 Min | Original 0.4 Min |
| mm | 3 Min | Original 3 Min |
Note:
Actuating Force:
To move the actuator from a free position, a certain amount of force is needed. This force may vary depending on different factors such as the weight and resistance of the load or the type of actuator being used. Nonetheless, some force will always be necessary to initiate movement and overcome any friction that may exist between the actuator and its surroundings. Therefore, it is important to consider the appropriate force required when designing an actuation system to ensure proper functionality and efficiency.
the operation position
2.4 Environment Resistance:
NO. | Item | Test conditions | Criteria |
2.4.1 | Cold | After testing at -25±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | Contact resistance(item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±10% of specified value . No abnormalities shall be recognized in appearance and construction. |
2.4.2 | Dry heat | After testing at 105±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. | |
2.4.3 | Damp heat | After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | |
2.4.4 | Change of temperature | After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | |
2.4.5 | Salt mist | Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water | No remarkable corrosion shall be recognized in metal part |
2.5 Welding Characteristics:
2.5.1 |
Solder ability | Switch test under such conditions and inspect after. 1）Variable temperature range ：235±5℃； 2）Dip time：3±0.5s； |
The area of dip tin should capture the 95% impregnated area |
2.5.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time Trial measuretemperature（℃）Time（s）Slot welding method260±55±1Soldering method350±53±0.5
|
All of the appearance, motor functions, electrical properties are no abnormal. |
3.Drawing & Dimension:
4. Circuiy Diagram:
5.Remarks
PARTS LIST:
Item | Name | Material |
1 | House | Nylon |
2 | Shaft | Nylon |
3 | Button | Nylon |
4 | Soldering Terminal | Brass Strip |
5 | Moving Terminal | Bronze Strip |
6 | Support | Copper Strip |
7 | Compressed Spring | Stainless Steel Wire |
8 | Top Column | Brass Strip |
9 | Contact | AgCdO / Copper |
Returned plastic should not exceed 20%.
6.Delivery,shipping and service
7.FAQ
Hot Tags: momentary rocker switch, China momentary rocker switch manufacturers, suppliers, factory