Technical parameters
2.1 General
2.3 Operating Characteristics:
Characteristics | Units | Standards | Note |
| N | 4±1.5 Max | Original 4±1.5 . |
Contact Force | N | 0.4 Min | Original 0.4 Min |
| mm | 3 Min | Original 3 Min |
Note:
Actuating Force:
Moving the actuator from the free position necessitates a certain amount of force.
the operation position
2.4 Electrical Specification:
NO. | Items | Test conditions | Requirements |
2.4.1 | Contact Resistance | Shall be measured at 12A 24VDC by voltage drop method after some operations without load. Applied position: Between terminal and terminal | 30mΩ MAX |
2.4.2 | Insulation Resistance | Test voltage:500VDC, measured after 1 min ±5s Applied position: 1)Between terminal and terminal 2)Between terminal and ground | 100MΩ MIN |
2.4.3 | Voltage proof | Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal and terminal :2000VAC/min (50~60Hz) 2)Between terminal and ground: 2500VAC/min (50~60Hz) | No dielectric breakdown shall occur |
2.5 Environment Resistance:
NO. | Item | Test conditions | Criteria |
2.5.1 | Cold | After testing at -25±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | Contact resistance(item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±10% of specified value . No abnormalities shall be recognized in appearance and construction. |
2.5.2 | Dry heat | After testing at 105±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. | |
2.5.3 | Damp heat | After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | |
2.5.4 | Change of temperature | After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | |
2.5.5 | Salt mist | Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water | No remarkable corrosion shall be recognized in metal part |
2.6 Welding Characteristics:
2.6.1 |
Solder ability | Switch test under such conditions and inspect after. 1）Variable temperature range ：235±5℃； 2）Dip time：3±0.5s； |
The area of dip tin should capture the 95% impregnated area |
2.6.2 |
Resistance to soldering heat |
The switch will be inspect under such conditions below Temperature and impregnated time Trial measuretemperature（℃）Time（s）Slot welding method260±55±1Soldering method350±53±0.5
|
All of the appearance, motor functions, electrical properties are no abnormal. |
2.7 Durability:
NO. | Item | Test condition | Criteria |
2.7.1 | Endurance (According to UL61058) | 13A 125VAC Switch shall be operated according to following sequence (Test1~Test2) VoltageCurrentPower factorOperation rateNumber of operationTest1125V14A0.75-0.86-10cycles/min50cyclesTest2125V13A0.75-0.86-10cycles/min6000cyclesVoltage proof(Cut-off current:0.5mA) 1GPA 125/250VAC ; Switch shall be operated 6,000 cycles at 15-20 cycles/min. Test voltages shall be applied for 1 min | Insulation resistance(item 4.2): 30MΩ MIN Voltage proof: Terminal and ground:1000VAC No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±20% of specified value . 6000 cycles temperature rise:30℃ MAX; 10,000 cycles temperature rise:55℃ MAX;
No abnormalities shall be recognized in appearance and construction |
2.7.2 | Endurance (According to EN61058-1 /IEC61058-1) | 10 (8) A 250VAC Switch shall be operated 10,000 cycles at 15~20 cycles/min Voltage proof(Cut-off current:0.5mA) Test voltages shall be applied for 1 min. | Insulation resistance(item 4.2): 50MΩ MIN Voltage proof: Terminal and terminal:750VAC Terminal and ground:1500VAC No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±20% of specified value . Temperature rise:55℃ MAX No abnormalities shall be recognized in appearance and construction |
3.Drawing & Dimension:
4. Circuiy Diagram:
5.Delivery,shipping and service
6.FAQ
For 27 years, SWITECH ELECTRONICS CO.,LTD has been specialized in manufacturing miniature switches applied in a variety of appliances, such as Micro switch, Tactile switch, Waterproof switch, Rotary switch, Rocker switch, Slide switch, Toggle switch, Push button switch, etc. Our clients include Panasonic, Siemens, Whirlpool, Electrolux, Eaton, Emerson. In order to be more competitive in price, our company opened its factory in China, 2003. Today, we have 1050 employees to sincerely provide our service from the factory in Taiwan, and 2 factories in Chinese Mainland. Annual output has reached 200 million pcs.
Hot Tags: splash proof rocker switch, China splash proof rocker switch manufacturers, suppliers, factory