Technical parameters
2.1 General
The 706-2 toggle switch is specifically designed for electronic equipment applications. This specification is exclusively applicable to this particular switch model. Its primary function is to control the circuit by providing an option to toggle between two different positions. By rearranging the original information, a highly similar content can be generated.
2.1.2 Operating temperature range 0℃ ～ +105℃
If no specific instructions are given, the tests and measurements shall be conducted under the following atmospheric conditions. .It is important to note that the generated content should be significantly different from the one generated by ChapGPT as it should reflect the original text's information using a different language model.
。，，。，。，，。
。。，，。，，、。，、，。
，。，。，，。
，。，，。
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any confusion arising from the verdict, certain evaluations need to be conducted under specific circumstances.
2.3 Mechanical Properties
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.3.1 | Operating Force | At the front end of the operation section, a static load measurement was taken in the direction of operation. The load was recorded at 1000 - 500 gf. Please generate a distinct and similar piece of content using the information provided. | According to the Recognition Chart |
2.3.2 | Terminal Strength | Front row feet is the measurement where any square type plus (1000gf) strength test can be performed in just 1 minute. | The terminals have been thoroughly inspected to ensure that they meet both mechanical and electrical standards. No abnormalities, such as cracks or loosening, have been found in the terminal connections. |
2.3.3 | Solder adhesion | Confirmation after testing under the following conditions： soldering temperature：270℃ immersion time：3±0.5 seconds Dip flux in room temperature for 5-10 seconds | 90% of the immersed part must be tin-coated |
2.3.4 | Solder resistance | Confirmation after testing under the following conditions： soldering temperatureimmersion timeManual solder365~370℃2~3 secondsAutomatic solder270+2℃10±1 seconds | There is no serious distortion in appearance, and it can work normally. |
2.4 Endurance
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
2.4.1 | Load life (A) (UL1054 standard) | 16A 125VAC The switch is tested in the order of Test 1 and Test 2. VoltageSteady currentpower factorTest 1125V20A0.75~0.8Test 2125V16A0.75~0.8Opening and closing speed（cycles/min）Opening and closing speed（cycle）Test 16~1050Test 26~106,000 | After Experiment 2： The rated current and insulation resistance can be switched on and off after the test. (3.5.2)100MΩMin. Withstand voltage AC 1000V No insulation damage after 1 minute test, Operating Force（3.1.1）Within the range of + 10% or - 30% of specifications. No abnormal appearance structure, Temperature rise: below 30℃ Max |
2.4.2 | Load life (B) (UL1054 standard) | 10A 277VAC The switch is tested in the order of Test 1 and Test 2 VoltageSteady currentpower factorTest 1277V15A0.75~0.8Test 2277V10A0.75~0.8Opening and closing speed（cycles/min）Opening and closing speed（cycle）Test 16~1050Test 26~106,000 | |
2.4.3 | Load life (C) (EN61058-1 standard) | 16(6)A 250V~T125 The switch is tested 10,000 cycles (7.5 cycles/min) according to the following circuit diagram. VoltageSteady currentpower factorTest 1250V4A0.6 VoltageSteady currentpower factorTest 1250V16A1.0 | Open and close after test, Rated current insulation resistance 100MΩMin. Measurement of AC 1125V(50~60Hz)between open contacts and poles Measurement of AC 2250V (50~60Hz) between terminal and grounding Fixed time: 1 minute each No insulation damage after test. Operating Force（3.1.1项）Within the range of + 10% or - 30% of specifications. No abnormal appearance structure, Temperature rise: below 55℃ Max |
2.7 Storage Method:
（1）If the product is not used immediately, it should be kept at normal temperature without direct sunlight and corrosive gases.
In the environment. But we recommend that we use it as soon as 6 months.
（2）Put the finished products in plastic bags and seal them in the same environment as soon as possible, and use them as soon as possible. Do not overlay excess when saved in order to prevent the pressure from breaking.
（3）Do not overlay excess when saved in order to prevent the pressure from breaking.
3.Drawing & Dimension:
4. Circuiy Diagram:
5.Product application
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on; 5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
6.Remarks
PARTS LIST:
NO. | PART NAME | QTY | MATERIAL |
1 | NUT | 2 | STEEL Ni PLATED |
2 | WASHER | 1 | STEEL Zn PLATED |
3 | LOCKING WASHER | 1 | STEEL Zn PLATED |
4 | BUSHING | 1 | BRASS Ni PLATED |
5 | BRACKET | 1 | STEEL Zn PLATED |
6 | TOGGLE HANDLE | 1 | BRASS Cr PLATED |
7 | COVER | 1 | NYLON 66 GLASS REINFORCED |
8 | HOLDER OF TIP | 1 | POLYBUTYLENE TEREPHTHALATE(PBTP) GLASS REINFORCED |
9 | SPRING | 2 | PIANO WIRE OIL |
10 | TIP | 2 | MELAMINE/PHENOLIC |
11 | ARM | 2 | COPPER Ag PLATED |
12 | MOVABLE CONTACT | 2 | Ag ALLOY |
13 | STATIONARY CONTACT | 2 | Ag ALLOY |
14 | TERMINAL | 2 | COPPER Ag PLATED |
15 | TERMINAL | 2 | COPPER Ag PLATED |
16 | BODY | 1 | PHENOLIC |
17 | LABEL | 1 | PVC |
Returned plastic should not exceed 20%.
7.Delivery,shipping and service
8.FAQ
Q:When can I get the quotation?
A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.
Q: Which payment form you can accept?
A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.
Q: How many packaging do you have?
A: We have three packages including bag, carton, barrel, usually it is
Q：Would you have a discount if l have a large order?
A：Yes we could offer different discount according to your order quantity.
Hot Tags: 2 way toggle switch, China 2 way toggle switch manufacturers, suppliers, factory