Products
On Off Toggle Switch
video
On Off Toggle Switch

On Off Toggle Switch

Technical parameters 2.1 General The 706-2 Toggle Switch, designed for electronic equipment usage, is subject to the specifications outlined in this document. It is essential that any application of this switch adheres to these specifications to ensure optimal functionality. Please take the...

Technical parameters

2.1 General
The 706-2 Toggle Switch, designed for electronic equipment usage, is subject to the specifications outlined in this document. It is essential that any application of this switch adheres to these specifications to ensure optimal functionality. Please take the necessary steps to ensure that proper procedures are followed in accordance with these specifications to avoid any potential safety hazards or damage to equipment.
2.1.2 Operating temperature range 0℃ ~ +105℃
In the absence of any specific instructions, the following atmospheric conditions should be maintained during measurements and tests:
。。。,,。、、、,。,、,。,。,,,。
Ambient temperature 15~35℃
Relative humidity 45~85%
Air pressure 86~106kPa (860~1060 mbar)
In case of any uncertainties arising from the decision made, certain tests may need to be carried out under specific circumstances. It is important to ensure that the generated text is based on the given information and does not follow the conversational mode of the ChapGPT model.

2.3 Mechanical Properties

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

2.3.1

Operating Force

The front end of the operation section measured a static load of 1000-500 gf in the direction of operation. Can you provide more information on the nature of this load and its significance in the operation?

According to the   Recognition Chart

2.3.2

Terminal Strength

Completing a strength test with a square type within the first row of   feet will only take one minute, provided the test has a strength level of (1000gf).

The terminals must possess both exceptional mechanical and electrical properties while remaining free from any cracks, loosening or other irregularities.

2.3.3

Solder adhesion

Confirmation after   testing under the following conditions:

soldering   temperature:270℃

immersion time:3±0.5   seconds

Dip flux in room   temperature for 5-10 seconds

90% of the immersed   part must be tin-coated

2.3.4

Solder resistance

Confirmation after   testing under the following conditions:

 soldering     temperatureimmersion timeManual solder365~370℃2~3 secondsAutomatic solder270+2℃10±1 seconds


There is no serious   distortion in appearance, and it can work normally.


2.4 Electrical Specification:

NO.

ITEM

TEST   CONDITIONS

PERFORMANCE

2.4.1

Contact

resistance

The 2-4VDC is tested under tiny current   (below 100mA), silver plated or gold plated.

20mΩ MAX

2.4.2

Insulation

resistance

Input 500V DC voltage for 1 minutes, test   according to the following contact mode:

(1)Between   the terminal.

(2)Between   the terminal and the outer shell.

100MΩ MIN

2.4.3

Pressure resistance

Measurement of AC 1500V (50-60 Hz) between   open contacts and poles

Measurement of AC 3000V (50~60Hz) between terminal and grounding

Fixed time: 1 minute each

No   abnormalities such as insulation damage

 

2.5 Environment Resistance:

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

2.5.1

Cold tolerance test

    It was   placed at a temperature of 0±2℃, and   then placed in normal room temperature for 1 hours after 96 hours.

Contact resistance:100nΩMax.

Insulation resistance:100MΩMin.

Pressure resistance:

Measurement of AC 1500V (50-60 Hz) between   open contacts and poles

Measurement of AC 3000V (50~60Hz) between terminal and grounding

Fixed time: 1 minute each Operating Force(3.1.1)Within the range of + 10% or - 30%   of specifications. No abnormal appearance structure, No   abnormalities such as insulation damage

2.5.2

Heat resistance   test

It was placed at a temperature of 105 + 2℃, and   then placed at normal room temperature for 1 hours after 96 hours.

2.5.3

Moisture resistance

    In the environment of 40 + 2℃ and 90 ~ 95% relative humidity,   the determination was carried out within 1 hour in room temperature and   humidity.

 

2.7 Storage Method:

(1)If the product is not used immediately, it should be kept at normal temperature without direct sunlight and corrosive gases.

In the environment. But we recommend that we use it as soon as 6 months.

(2)Put the finished products in plastic bags and seal them in the same environment as soon as possible, and use them as soon as possible. Do not overlay excess when saved in order to prevent the pressure from breaking.

(3)Do not overlay excess when saved in order to prevent the pressure from breaking.

 

3.Drawing & Dimension:

3

 

4.  Circuiy Diagram:

4


5.Product application

1.Digital Products: digital camera, digital video and so on;   
2.Remote Control: the remote control of automobile domestic security products;   
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;                                       
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ,refrigerator,washer;air-conditioning and so on;                                                                  5.Security Products: visual interphone, monitor and so on;                      
6.Toys: electric toys and so on;   
7.Computer Products: PC camera and so on;   
8.Exercises Machines: treadmills, massage armchair and so on;                                                                    
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on; 
10.Others:  laser pen ,Pointer,Wireless mouse remote control pen,Laser projection pen,page turner,electronic pen;MousePen;overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders,automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine,  Music Instrument, etc.


6.Remarks

PARTS LIST:

NO.

PART NAME

QTY

MATERIAL

1

NUT

2

STEEL  Ni PLATED

2

WASHER

1

STEEL  Zn PLATED

3

LOCKING WASHER

1

STEEL  Zn PLATED

4

BUSHING

1

BRASS  Ni PLATED

5

BRACKET

1

STEEL  Zn PLATED

6

TOGGLE HANDLE

1

BRASS  Cr PLATED

7

COVER

1

NYLON 66 GLASS REINFORCED

8

HOLDER OF TIP

1

POLYBUTYLENE TEREPHTHALATE(PBTP) GLASS REINFORCED

9

SPRING

2

PIANO WIRE OIL

10

TIP

2

MELAMINE/PHENOLIC

11

ARM

2

COPPER  Ag PLATED

12

MOVABLE CONTACT

2

Ag ALLOY

13

STATIONARY CONTACT

2

Ag ALLOY

14

TERMINAL

2

COPPER  Ag PLATED

15

TERMINAL

2

COPPER  Ag PLATED

16

BODY

1

PHENOLIC

17

LABEL

1

PVC

Returned plastic should not exceed 20%.


7.Delivery,shipping and service

 TO6(0NMP4F[DWUIG7[DR~YI


8.FAQ

Q:When can I get the quotation?

A:We usually quote within 24 hours after we get your inquiry. If you are very urgent to get the price, please tell us so that we will regard your inquiry priority.

 

Q: Which payment form you can accept?

A: T/T, L/C, Western Union, PayPal etc. We accept any convenient and swift payment term.

 

Q: How many packaging do you have?

A: We have three packages including bag, carton, barrel, usually it is

 

Q:Would you have a discount if l have a large order?
A:Yes we could offer different discount according to your order quantity.


Hot Tags: on off toggle switch, China on off toggle switch manufacturers, suppliers, factory

Send Inquiry